We do offer bolt-on spare tire carriers like the Fulton # FSTC1000301 which provides a bit over 7-inches of lift for better ground clearance. In many cases this will provide much better clearance than a simple u-bolt type carrier like # CE22007Z-11050-2. All spare tire carriers, including the hitch-mount type like # C31006, can be seen on the page I linked for you. view full answer...
The Equal-i-zer Weight Distribution System 10K which is what I recommend for a Lance 2375 Travel Trailer can be obtained with the shank as part # EQ37100ET or without as part # EQ37101ET. The most common reason others purchase the system without the shank is so they can go with a larger hitch size or longer shank to clear the tailgate.
The Equalizer Shank part # EQ90-02-4500 should allow most trucks to lower the tailgate without hitting the jack. I wouldn't say it's too much at all but... view full answer...
Our part # 5AB-E510-710 is exactly the part number you are looking for. This is a cushioned 5th Airborne pin box designed to fit several common pin box styles like the:
Fabex (500, 503, 765, and 770)
Lippert (1716)
RBW (7028) view full answer...
Trailer brake magnets will eventually wear out since they grab to the drum as the wheel is turning but they don't have a set lifespan. Typically most of the time they last between 20 and 25 thousand miles. As long as they are working and don't look worn out with windings showing through you are fine. view full answer...
I would recommend using the Andersen Rapid Jack # AM3620 over the FloTool RhinoRamps # FT11909MI. You will have issues with the length of the RhinoRamps and the 2nd axle trying to move up and sit on the ramp due to its length. The Andersen is much shorter at 17" versus 35-1/2" of the RhinoRamps.
The Andresen unit also takes up less room and can serve multiple uses as it can work as a wheel chock if needed. view full answer...
Yes, an AL KO 5200 lb axle would have a 42 spindle on it. The bearing # 25580 that you referenced is an inner bearing for this spindle/axle. view full answer...
You can replace your SW6DE water heater with a Furrion Tankless water heater # FR93FR. Generally the tankless units are smaller than the tanked units. So some modification may be required to allow the tankless unit to fit correctly.
As far as the door, I cannot tell you exactly what size you will need to cover your cutout. You will need to measure your cutout and order a door large enough to cover it. We have the door available in a 16" x 16" # FR43FR, 16" x 18" # FR63FR or the 18" x... view full answer...
In order to pick out a direct replacement for the landing gear on your trailer we would need to know the distance between the mounting brackets. Otherwise you could just have the brackets removed from your trailer by a qualified welder and then install the brackets that come with the Reese Bulldog Tandem Landing Gear Set # RP500708 that you referenced. This would be a great option for your 2005 Keystone Everest 293P. Either way this landing gear set would work well for you, you just might... view full answer...
The part # 37207-31235 will give you 12 feet of hose that will attach to the quick disconnect you have on your RV. For an adapter then we have the part # 401132-MBS which gives you a male quick disconnect on one side and a 1/4 inch MPT fitting on the other like you described needing. view full answer...
Without knowing more info it's hard to know for certain what reservoir you'd need but we do have the Lippert # LC46FR which is a 2 quart reservoir for the Lippert hydraulic kits.
If your trailer had the # LC141111 this would be the correct replacement reservoir. view full answer...
Yes you are on the right track. Sounds like you landing gear legs have internal problems that a gear kit like the part # LG-146060 should fix as you've replaced basically everything else. This kit is for the follower leg so for a driver leg as well you'd want the # LG-146059. view full answer...
To replace the Dometic air conditioner in your 2018 Keystone Cougar 5th Wheel I recommend the Furrion Chill Replacement RV Air Conditioner for Furrion Setup - 15,000 Btu - White # FR58PR or Black # FR86PR.
We have found the Furrion Chill to be one of the quietest AC options due to the rubber dampers, and its 15000 BTU rating and dual fans with dual motors will do a great job at keeping your RV cool.
These units are compatible with air duct your Dometic unit uses. view full answer...
I would be happy to help, but you are correct we do not have your 2007 Keystone Everest 5th wheel trailer in our fit guide so you will need to measure your current brakes to determine the correct replacements.
To do this you will need to remove one of your hubs and measure the diameter, and depth as shown in the included diagram.
The most likely two options are the 10" x 2-1/4" # AKEBRK-35-SA which are used on 3500lb axles, or the 12" x 2" # AKEBRK-7-SA.
I included a few video reviews... view full answer...
I would be happy to help!
Since your 2018 Keystone Cougar 311 RES 5th wheel with tandem 5200lb Dexter axles has the Dexter 072-097-00 leaf springs currently installed the 5-Leaf Double-Eye Spring for 6,000-lb Trailer Axles - 25-1/4" Long # e34SR you were looking at will be an exact replacement for you.
These leaf spring are the same length at 25-1/4" and the 6000lb capacity of the # e34SR will give you the extra support you are looking for.
For replacement U-Bolts I recommend four of... view full answer...
Yes, you can use the Bauer Products RV Baggage Door Slam Latch - Black # BA57FR to replace an old or damaged slam latch on your 2019 Keystone Cougar 5th Wheel 315RLS.
It is 5 inches wide, 4-1/2 inches tall and 1-1/2 inches thick.
It will fit cutouts measuring 3-1/4 inches tall and 4 inches wide.
It also comes with a one year limited warranty. view full answer...
For a set of self adjusting brake assemblies that will fit the hub/drums of your 2006 Keystone Laredo 25RK based on the info you mentioned the part # 23-458-459 would be what you'd want.
If you needed a new hub/drum the part # AKHD-655-6-EZ-K would work as well. This is pre-greased too which means you'd be able to install it without having to pack bearings. view full answer...
From previous customers we have learned that the 2001 Keystone Cougar 276RLS has 4,400 lb axles and a bolt pattern of a 6 on 5-1/2 inch bolt pattern so for a replacement hub the correct and only option is the part # 8-407-5UC3-EZ. view full answer...
The first thing you will need to do is determine the bolt pattern you have now. If you don't already have this information you can check for the pin box number on the pin box sticker, identify it with the serial number through Lippert, have Keystone identify it with your VIN number, or measure the bolt pattern. I have attached an article below which explains how to measure.
Once you have this information you will be able to find a 5th wheel to gooseneck pin box that fits your current bolt... view full answer...
You can use the Replacement Lead Jack w/ Drop Leg for Stromberg Carlson Landing Gear part # LG-179013 which has an outer tube that measures 29-1/2" long and is the standard RV leg replacement for several brands like Lippert, LCI, Venture, Stromberg etc. view full answer...
The cover I recommend for a 2021 Keystone Cougar Fifth Wheel 368MBI is the Camco UltraGuard 5th Wheel Cover part # CAM45759. This cover has triple layer top panel which will help reduce snow accumulation on top of the cover and help it run off when it melts. It also has integrated self-adjusting hold-down straps which prevent the cover from flapping in windy conditions. It also has zippered panels for entry.
The cover does not cover the wheels however but that's the case for most if not... view full answer...
Go To Results